You open Synology Assistant or go to find.synology.com and, instead of a NAS that says “Ready”, you see “Not Installed”, “Migratable” or “Configuration lost”. The web page offers to install DSM for you, and it is very tempting to click straight through. Before you do, it is worth understanding what each status means, because one wrong choice in that wizard can turn a recoverable problem into a wiped volume.
Why a Synology suddenly says it has no DSM
DSM, Synology’s operating system, is not stored on a chip inside the NAS. It lives in a small system partition that is copied onto every disk in the unit. When the NAS starts, it looks for that system partition on the disks. If it cannot read a usable copy, it reports that DSM is not installed, even though your shared folders may still be sitting untouched in the data volume.
The most common triggers are:
- a DSM update that was interrupted, for example by a power cut or someone pulling the plug while it “hung”
- a power cut or brownout during normal running
- disks moved into a different or new Synology model
- a reset button pressed for too long, or pressed twice
- one or more disks failing, so the NAS cannot read the system partition reliably
What the statuses usually mean
Not Installed
The NAS cannot find a working DSM on the disks. This can be a damaged system partition after an update, but it can also mean the unit cannot read the disks properly at all. If the status appeared together with clicking, beeping, a disk light showing orange, or a disk that recently gave warnings, treat it as a possible disk failure rather than a software fault.
Migratable
The disks contain DSM from another unit or an older version. You will normally see this after moving disks into a new NAS, or after an update that did not complete. Synology’s migration is designed to keep data, but only if you choose the option that keeps it.
Configuration lost
Usually seen after a reset. The settings have been cleared and the NAS wants DSM reinstalling. Again, the data volume is not necessarily affected, but the next steps matter.
The choice that loses data
The installation wizard can lead to a reinstall that keeps your files, or to a clean installation that erases the disks. The screens are not always read carefully when someone is stressed and staff are waiting for the shared drive. Our advice is simple:
- Read every screen in full before clicking Next.
- If any option mentions erasing, deleting all data, a clean install or creating a new storage pool, stop.
- Never let the wizard “repair” or create a storage pool or volume on disks that hold the only copy of your data.
- If you are not sure which option keeps your data, do not guess.
Even a reinstall that keeps data writes a fresh system partition to every disk. On healthy disks that is normally fine. On a disk that is already failing, the extra writes and the rebuild activity that follows can push it over the edge, and if the volume was already degraded, a second weak disk can take the whole pool with it.
Safe checks before you do anything else
- Take a photo of the screen. Note the exact status, the model and the DSM version shown.
- Check the disk lights. A disk showing orange, or no light at all, points to hardware rather than software.
- Listen. Clicking, repeated spin-up sounds or beeping from the NAS are reasons to power it down and leave it off.
- Do not swap disks around. Keep every disk in its original bay, and label them if you remove them. Bay order matters for the RAID layout.
- Do not put the disks in a Windows PC. Windows cannot read Synology volumes and may offer to initialise them, which overwrites the start of each disk.
- Check your backups. If you have Hyper Backup, a USB copy or cloud copy, confirm it is current before you touch the NAS again. A good backup makes a clean reinstall a reasonable option.
When the volume needs recovery rather than a reinstall
Stop and get professional help if any of these apply:
- there is no backup of the data on the NAS
- a disk had warnings, bad sectors or a “Degraded” status before the NAS stopped
- the NAS shows fewer disks than are fitted
- a reinstall has already been attempted and the volume now shows as crashed or missing
- someone has already tried a clean install or created a new pool
In the lab we work from images of each disk rather than the originals, reassemble the Synology RAID (SHR or classic RAID) and the Btrfs or ext4 volume from those images, and copy your shared folders off. Nothing is written to your original disks. You can read more about how we handle these units on our Synology data recovery page, and about larger multi-disk systems on our server data recovery page.
If you need to post the disks
You usually do not need to send the NAS enclosure, only the disks, numbered by bay. Pack each disk in an anti-static bag with plenty of padding, and include a note of the model, the RAID type if you know it, and what happened just before the status changed. Our UK data recovery service page explains how to get drives to us from outside London.
Talk to us before you click Install
If your Synology is showing “Not Installed”, “Migratable” or “Configuration lost” and the data matters, leave it switched off and call Data Doctor on 020 7394 2529 for a free initial consultation. You can also bring the disks to our clean room lab at Unit 1, The Willows, 80 Willow Walk, London SE1 5SY.