Your Synology NAS has stopped working. Perhaps it shows no lights at all when you press the power button, or the power light keeps flashing blue and the unit never appears on the network, in Synology Assistant or at find.synology.com. When the NAS box itself fails like this, the disks inside, and the data on them, are very often fine. What happens next decides whether it stays that way.
Is it the NAS or the disks?
A Synology NAS is a small computer with its own power supply, motherboard and memory. DSM, its operating system, is stored on the disks, and the data volume sits on the same disks in a separate partition. So a dead power supply or a failed motherboard stops the NAS from working without touching your files. Typical signs that the unit, not the disks, is the problem:
- Nothing at all happens when you press the power button: no lights, no fan, no disk spin-up.
- The power light flashes for a long time, the disks may spin, but the NAS never gets a network address.
- The NAS powers on, then switches itself off after a few seconds or minutes.
- It stopped after a power cut, a storm or a move to a new desk or cupboard.
By contrast, if the NAS starts normally but Storage Manager shows a crashed, degraded or missing volume, the problem is on the disks, and that needs a different approach.
Simple checks that are safe
- Power adapter. Many desktop Synology models use an external power brick. Check the light on the brick if it has one, try a different wall socket, and remove any extension lead or surge protector from the chain. Only use a replacement adapter with exactly the same voltage, polarity and connector, ideally the official part; the wrong one can damage the NAS.
- Network. Try a different network cable and router port, and look for the NAS in your router’s list of connected devices. Sometimes the NAS is running but has a new address.
- Allow time. After a power cut, a DSM update can take ten minutes or more. Give it time before deciding it is dead, but don’t leave it cycling on and off all day.
Don’t press the reset button. A reset is designed to clear network and admin settings rather than data, but it doesn’t help a unit that won’t start, and holding it for too long or repeating the procedure can lead to DSM reinstallation prompts that are easy to answer wrongly.
A known issue on some older Plus models
Some Synology Plus models from around 2014 to 2016, such as the DS415+ and DS1815+, use an Intel Atom C2000 processor. A fault in that processor family can stop the system from booting after some years of use: the unit typically shows a flashing power light, or no response at all, and never appears on the network. Synology published information and offered repairs at the time. If you have one of these models and it suddenly won’t boot, the board is a likely suspect, and the disks are usually unaffected.
What not to do with the disks
The urge to pull the disks out and get the files off them some other way is understandable. A few common moves cause real damage:
- Don’t connect them to a Windows PC. Windows can’t read Synology volumes, which use Linux software RAID with ext4 or Btrfs. It will offer to initialise or format the disks, and saying yes overwrites key structures.
- Don’t build a new volume in a replacement NAS. If the disks go into a new unit and you choose a fresh installation, or create a new storage pool, the old volume can be overwritten.
- Don’t mix up the order. Before removing anything, label each disk with its bay number. Keeping the original order is the safest approach in any later recovery or migration.
- Don’t run repair tools on individual disks. On a multi-disk volume, “fixing” one disk on its own can make the set inconsistent.
Moving the disks to another Synology
Synology supports moving disks into a compatible unit. The new NAS should detect them as Migratable, and the migration keeps the data volume as long as you choose the right option. We explain the screens and choices in our guide to Synology “Not Installed” and “Migratable” messages. This is a sensible route when the disks are healthy, you have a recent backup, and you are confident about which option to choose.
It is riskier when:
- there is no backup and the data matters, for example business files, client work or years of family photos;
- one or more disks were already showing warnings before the unit failed;
- the volume used encryption, or you aren’t sure how it was set up (SHR, RAID 5, RAID 1 and so on);
- the NAS died during a power cut, a DSM update or a RAID repair.
In those cases, the safer order is to make a sector-level copy of every disk first and work from the copies, so that a wrong choice on the new unit can’t touch the originals.
How we handle a failed Synology
At our London lab we work out whether the fault is the unit, the disks or both. Each disk is checked and copied, with any physical problems dealt with in our clean room. We then rebuild the volume from the copies rather than the original disks. Your data goes back to you on new storage, and the original disks stay unchanged. You can read more about our Synology data recovery service and our wider UK data recovery service.
Need help with a dead Synology?
If your Synology won’t power on or boot and the data isn’t backed up anywhere else, switch it off, label the disks and call Data Doctor on 020 7394 2529 for a free initial consultation. You can also bring it to us at Unit 1, The Willows, 80 Willow Walk, London SE1 5SY.