A hard drive that works one day and vanishes the next is easy to shrug off. It shows up after a restart, the files open, and it feels as though the problem has fixed itself. In practice an intermittent drive is one of the clearest warnings a disk can give: something inside it is failing, and each time it is powered on there is a chance it will not come back. This guide explains what the common patterns usually point to, what you can safely do, and what to avoid if the data matters.
The patterns people describe
Intermittent faults rarely look the same twice, but most fall into a few groups:
- It appears after several tries. The drive is not detected, then shows up on the third or fourth power-on or after a different cable.
- It works for a while, then drops out. Files open, then copying stalls, Explorer or Finder freezes, and the drive disappears.
- It only works when cold, or only once it has warmed up. Some drives start first thing in the morning and fail later; others are the reverse.
- It only works lying a certain way, or after a knock. A portable drive that works when held at an angle, or a desktop drive that starts after being tapped.
- It is slow some days and normal on others. Copies crawl, then speed up again for no obvious reason.
What each pattern usually points to
Only a proper diagnosis can confirm the cause, but these are the faults we most often associate with each symptom.
Weak or degrading read/write heads
Heads wear unevenly. A weak head can still read well enough when conditions are just right, and fail as the drive warms up or when it reaches a damaged area. Drives with weak heads often work for a few minutes, slow down, then stop responding. Repeated attempts to copy a large folder are hard on them, because the drive retries the same difficult areas over and over.
Sticking or failing spindle motor
If the platters do not spin up cleanly, the drive may need several attempts before it is ready. A faint hum, a buzz or a repeated spin-up sound before it is detected is typical. Tapping or tilting the drive to get it started can move the heads across the platter surface while the motor struggles, which is exactly how surface damage begins.
Electronic or connection faults
Not every intermittent fault is inside the sealed part of the drive. A cracked solder joint on the circuit board, a worn USB socket on a portable drive or a failing USB-to-SATA adapter in an external case can all make a healthy disk come and go. A drive that only works when the cable is held at an angle often points here. These faults are usually more forgiving, but the drive can still be damaged if it keeps losing power mid-write.
Bad sectors that are spreading
A drive that is slow on some days and fine on others may be struggling with a growing number of unreadable sectors. It looks normal until Windows or macOS tries to read a damaged area, then everything hangs while the drive retries.
Why every extra power-on matters
With most failing drives the damage is progressive. A head that is starting to fail can shed material onto the platter surface, and once that happens the remaining heads are at risk too. A drive that needed three tries this week may need ten next week, and then not start at all. That is why the best time to recover data from an intermittent drive is while it still works some of the time, before a recoverable fault becomes a much harder one.
What you can safely do
- Decide what matters most. If the drive is working right now and holds something irreplaceable, copy that first: one folder of photos or one set of documents, not the whole drive.
- Copy to a different, healthy drive. Never copy files to another location on the same failing disk.
- Stop at the first sign of trouble. If the copy slows sharply, the drive starts clicking or the computer freezes, disconnect it rather than waiting.
- Try one known-good cable and port, once. For an external drive, a different cable and a USB port directly on the computer (not a hub) can rule out the simplest connection faults.
- Keep it still and at room temperature. Use the drive on a flat, stable surface and avoid moving it while it is running.
What not to do
- Do not run CHKDSK, First Aid or third-party “repair” tools on it. They write to the drive and work it hard, which can turn an intermittent fault into a permanent one.
- Do not tap, shake or tilt the drive to get it going.
- Do not put it in the freezer. This old tip can cause condensation inside the drive and damage the platter surface.
- Do not leave it running overnight on a long backup or scan in the hope it finishes.
- Do not open the drive. Even small amounts of dust on the platters can make recovery much harder.
When to stop and get help
If the data is important and the drive is not behaving, the safest choice is to power it down and leave the next attempt to a lab. Our engineers assess the drive first, then work from a controlled image rather than the original wherever possible, and carry out any internal work such as a head replacement in our clean room. You can read more about our hard drive data recovery in London, how we approach hard drive repair for recovery, and our laptop data recovery services if the drive came from a laptop.
Talk to Data Doctor
If your hard drive keeps coming and going, call Data Doctor on 020 7394 2529 for a free initial consultation before you try again. We are at Unit 1 The Willows, 80 Willow Walk, London SE1 5SY.