You get back from a ride, a dive or a holiday, put the GoPro on the table and it says SD ERR or NO SD. Or the camera seems fine, but the clip you cared about is missing, will not play, or stops half way through. Action cameras are hard on memory cards: they write large files quickly, get knocked about, and often lose power mid-recording when the battery runs flat. The good news is that the footage is often still on the card. The bad news is that the most natural reaction, letting the camera reformat the card, is the one thing most likely to lose it for good.
Stop recording on that card
As soon as you notice a problem, take the card out and put it somewhere safe. Every new clip is written into free space on the card, and on a card with a damaged file system the camera may treat the space holding your missing footage as free. One short test recording can overwrite exactly the clip you are trying to save. If you need to keep filming, use a different card.
What SD ERR and NO SD usually mean
- NO SD – the camera cannot see a card at all. The card may not be seated properly, the contacts may be dirty or wet, or the card itself may have stopped responding.
- SD ERR – the camera can see the card but cannot read or write it properly. This can be a corrupted file system, a card that is too slow or not supported by that camera, or a failing card.
- Missing or broken clips – most often caused by power being lost while a clip was being written (flat battery, camera knocked off, card pulled out), which leaves the last file unfinished.
The camera will often offer to format the card at this point. Decline. Formatting creates a new, empty file system, and although some data may survive a quick format, every clip you record afterwards makes recovery harder.
Safe checks you can do yourself
- Check the card in a computer, not the camera. Put it in a decent USB card reader and see whether the files appear. If they do, copy the whole DCIM folder to your computer before doing anything else. Do not move or delete anything on the card itself.
- Try a second reader or computer if the card is not seen. Cheap readers and adapters fail more often than you would expect.
- Look at the contacts. If the card got wet, let it dry fully before trying again. Do not scrape the gold contacts.
- Try a different card in the camera. If a known-good card works, the problem is the original card, not the GoPro.
- If Windows or macOS asks to format the card, cancel. That message means the computer cannot understand the file system; it does not mean the clips have gone.
The LRV and THM files: a useful fallback
Many GoPro HERO cameras record more than one file for each clip. Alongside the full-quality .MP4 you will usually find a .LRV file (a low-resolution copy the camera uses for previews and the phone app) and a .THM thumbnail. If the main MP4 is damaged or missing but the LRV for the same clip is intact, you still have a lower-quality version of the moment. Copy the LRV file somewhere safe and change its extension from .LRV to .MP4 on the copy; most video players will then open it. It will not replace the original for editing, but for a once-in-a-lifetime clip it can be a lot better than nothing.
Clips cut short by a flat battery
When the battery dies mid-recording, the camera never gets to finish writing the end of the file, which is where much of the information a player needs is kept. Some HERO models offer to repair the last clip when you put the card back in and switch on. If you can, copy the card to a computer first, then let the camera try; that way, if the repair goes wrong, you have not lost the original. Avoid running several different “video repair” programs on the only copy, as some of them write changes back to the file.
What not to do
- Do not reformat the card in the camera or on a computer.
- Do not keep re-inserting a card that comes and goes; an intermittent card is often a failing one, and each attempt is a risk.
- Do not run CHKDSK or First Aid on the card. These tools “fix” the file system by discarding what they cannot understand, and that can include the clips you want.
- Do not install free recovery software onto the same card, and do not save anything recovered back onto it.
- Do not bend, cut or open a microSD card. Inside it is a single sealed package, and physical damage needs specialist handling.
When to bring it to a lab
If the card is not recognised by any reader, shows the wrong capacity, or the files appear but will not copy, the card itself has probably failed. MicroSD cards are monolithic devices: the controller and memory are sealed in one tiny package, so there is no simple part to swap. Recovering data from them is careful, specialist work, and the less the card has been used since the fault, the better the chances. We handle memory cards and USB flash media alongside hard drives and SSDs at our London lab; you can see the range on our data recovery services page, and how the process works across the UK on our UK data recovery page.
Once you have your footage back, keep two copies on different devices before the card goes back in the camera, and replace any card that has given an error once. It is far cheaper than losing the next trip.
Need help with a failed GoPro card?
Put the card away, do not format it, and call Data Doctor on 020 7394 2529 for a free initial consultation. You can also bring it to us at Unit 1 The Willows, 80 Willow Walk, London SE1 5SY.